Baofeng UV82 - Some Disappointing Facts

Baofeng UV82 - Some Disappointing Facts



How to Easily Add a Channel on the BaoFeng Handheld Radio (without a PC)

How to Easily Add a Channel on the BaoFeng Handheld Radio (without a PC)

Walk-through steps for manually programming the BaoFeng handheld radios. Easily program your BaoFeng for Repeater or Simplex Channels along with adding CTCSS or DCS settings.

This video demonstrates the programming on a BaoFeng UV-82HP. The same menu steps work on the BF-F8HP, UV-5R, UV-82, along with several other BaoFeng handhelds.




Baofeng UV-82L Basics

Baofeng UV-82C Kit Radio & Recommended Accessories



Chirp Programming Baofeng UV-82 - Scanning Receiver

End to End instruction on how the Baofeng UV-82 Radio was programmed as a Scanning Receiver for Fire Department Frequencies.


Baofeng UV-82 series Keyboard Programming

Baofeng UV-82 series Keyboard Programming
On the Fly Keyboard Programming


Several times I’ve been given the local repeater's information and perhaps I’m going to be in the area for a only few hours or maybe I’m not sure if I can hit it and want a quick way to try. Here is an easy to remember solution.

We will assume that you are familiar with the Keys and Functions.

Enter VFO mode

Select A or B to program in

Select the correct BAND

Enter the frequency you want to try

<Menu>   <13>   <Menu>     (enter tone, if req'd)     <Menu>

<Menu>   <26>   <Menu>   (check/change offset)   <Menu>

<Menu>   <25>   <Menu>   (check/change offset)   <Menu>

You are done.

You can “store” one frequency in each A and B and the UV-5R will retain these until the information is overwritten.

If you are entering a Simplex frequency, you need to reset the options of Menus 13 & 25 to OFF.

I remember the MENU #’s this way...    13,  26,  25
Unlucky Number =
Double Unlucky =
Back Off   (-1)   =     13
26
25
Cut the 7 steps out and put in your wallet for later use.
This would also be a quick way to confirm that your radio is working.
  

UV82 series Programming Memories Manually

UV82 series Programming Memories Manually

The following steps must be followed exactly.
Do NOT skip any steps along the way.

Frequency Mode vs. Channel Mode
These two modes have different functions and often confused.

Baofeng UV-82 Switching Between Memory and VFO (Frequency) Mode

While the UV-82 is pretty much a UV-52 in a new wrapper, they left off the V/M button that allows you to change between Memory/Channel mode and the VFO where you can choose any frequency. I'm assuming this was directed at business-type users, who didn't want their employees having the ability to use any frequency the radio could access. In this video, I quickly review how to change between the modes.


Baofeng UV-82 series Manually Reprogramming a Channel

Baofeng UV-82 series Manually Reprogramming a Channel
Changing Channel Data


     It is possible to change the TRANSMIT settings of an existing channel by making the change then re-saving the data. It is NEVER possible to change any of the RECEIVE settings without deleting the entire channel [menu, 28] and starting over.

   This radio saves the receive data and the transmit data separately in the same channel number. Everything about the receive conditions must be set and saved first (which is all you need for a basic simplex channel with no Tx tone etc.)

   All TRANSMIT settings (including any tone, code or having the Tx frequency showing in the display) must be set and saved separately to create a complete channel. If you were to save updated data to that same channel a second or third time, you would ONLY replace the previous TRANSMIT data without ever altering the saved RECEIVE data.

   If the RECEIVE channel is improperly programmed, the channel must be totally deleted and reprogrammed.

Important note:
So, it really is possible to change the Tx tone, but it is quite a bit more complicated than just changing the menu setting. You need to:
       Change the menu setting
       Ensure that the TRANSMIT frequency is displayed in the top display
       Save the complete transmit data back to the same channel.

   Most people forget to have the transmit frequency displayed and save the Transmit data with the receive frequency displayed. That will accidentally create a simplex channel.

   The radio acts much like a computer… it does what you tell it to do, not necessarily what you want it to do.

Baofeng UV-82 Series - Menu Definitions

0    SQL     Squelch Level-  Squelch silences the receiver when there is no signal.

-  UHF Sensitivity can be varied from .1 to .3 mV
-  VHF Sensitivity is constant. 1 > 9 = .1 mV
-  Level 0 = Open Squelch
-  There is little difference between settings.
          Level 5 is recommended.
      0 > 9
1    STEP     Frequency Step
-  Amount of frequency change when using Up/Down arrows or when scanning in VFO Mode. 

      2.5 / 5 / 6.25 / 10 /
  12.5 / 25 / 50  kHz
2    TXP     Transmit Power
-  High = 5 watts    Low = 1 watt
-  Use Low power unless necessary.
-  Power can be toggled Hi/Lo by pressing the [ # ] key,
    however, Dual Standby (Menu 7) must be OFF.

      High / Low
3    SAVE     Battery Save
-  Sleep Ratio to acknowledge an RX signal.
-  The higher number increases the RX sleep cycle, but you may miss the first few syllables before the RX opens.
         1=1:1    2=1:2    3=1:3    4=1:4